Ans: We don’t have more than 18 loops panels but for big requirements we can use multiple panels in a network.
Ans: Drift compensation
2. Day night mode
3. Five different modes in multisensor
4. Five Response times.
Ans: Max 10 Zone monitor modules suggested by Apollo in a single loop.
Ans: Yes we can connect 200 detectors but it should be Soteria protocol detectors.
Ans: 128 X 64 Characters LCD display.
Ans: V.252.X Series panels have unique features to make XP95 detectors blinking and continuous RED LED glow in alarm state.
Ans: Yes we can connect max. 16 panels in peer to peer networking. Those can be repeater panels or main Fire panels.
Ans: Yes, It is possible. We can export events through mini USB port by using pendrive.
Ans: Max. 1200 meter.
Every accessible door and operable window should be protected. All glass windows should be also protected.
Door magnetic contact is visible.
Our system is work on both type of sensor it may be wired or wireless.
Typically, alkaline batteries is used and it must be changed every year. We have Door Magnetic sensor which provides battery Life is up to 5years.
Alkaline batteries can be purchased at any hardware store for a few rupees. Lithium batteries are more expensive and probably must be purchased through the security company, although they are becoming more common.
Normally 24hr (v-cop Silver PSTN)/12Hr (V-cop silver-GSM) backup is provide (sensor supply is not provided by panel).
Portable devices like pendant panic buttons should not be supervised because you often will leave the premises with them for several hours. Since they don't check in, you will have to test them manually every month or so....
Not required/depending upon site.
One fire zone is available in the panel. (Max 20 smoke detector is used).
Most alarm systems today come standard with pet friendly motions. So pets up to 40 pounds will not be detected. But it's always a good idea that when you get an alarm system to let your pet run around in front of the motions to make sure they aren't detected. Even when your home alarm isn't armed, the motion will still have a display is show when it sees motion.
In most multi story homes it's almost impossible for hardwired home alarm systems to be installed because of having no attic to run the wires. But with our state-of-the-art wireless home alarm systems, no wires need to be run. That means it doesn't matter how many stories your home is you can still get an alarm system setup in your house.
Wireless alarm systems come with a host of other advantages as well. Many experts cite their outstanding range as an essential asset – some of the best systems can communicate readily over hundreds of feet without difficulty, effectively doubling the size of the dragnet you deploy. For homeowners with large properties or anyone looking to cover a greater swath of territory, simple solutions like these let you create vast and effective networks quite literally out of thin air. You also have an option to install a wireless extender/booster.
A motion detector may activate falsely due to improper installation of the device above a heater or furnace. Movement of objects such as balloons, blinds, and curtains within the range of a motion detector may also trigger alarm activation. The motion detector may require relocation or adjustment by a Response Alarms technician. The batteries may also be weak
Yes, System is work on two mode. First is all arming mode and second is perimeter arming.
In night if you have required to set the system is in alarm mode so select the “perimeter Arming” of the system.
(Yes, and we always advise you do. We can program the system to include only those areas of the premises that you want protected and exclude others for the 'night' setting. It is more disturbing to be burgled when you are asleep then when you are out of the house!)
A: TS230HLB is Standalone Type. TS12HLRB can be integrated with Home Automation & Security System provided that these systems have NO & NC contacts.
A: Detector is Auto Resettable.
A: The performance of Gas Leak Detector is not measured in terms of range. When gas leaks & the gas particles reach the sensor & when concentration reaches 10% of LEL, warning is given. Hence, we recommend to position or place this device as close as possible to the gas source.
A: Fully battery-operated Gas Leak Detectors are not available anywhere in the world. Reason being the current consumed by such device/ detector/ sensor would drain the standard battery within 6-7 days. Hence, it is not practical to keep replacing the batteries after every 7 days. We do not supply battery operated gas leak detector. However, we do have model with rechargeable battery backup. In case of power failure this detector with rechargeable battery will switch to battery mode.
A: No. It is not dangerous to have an electrical socket near the gas source. In any typical kitchen there are several electrical home appliances which operate on electricity when connected to the electrical socket like Mixer, Grinder, Fridge, Oven etc. In case of leakage of gas & gas concentration reaching LEL then somebody might switch the power ON/Off, the spark which happens at the switch contact might cause fire. Our detector gives warning much ahead of dangerous level. Also, no switching happens inside the circuit as the circuit is solid state. Hence, it’s not dangerous to have an electrical socket near the gas source.
A: Life of the sensor inside Gas Leak Detector is 2-3 years. We recommend replacing the gas leak detector after 2 years of use.
A: The best location to fix is near the Gas Cylinder or near the pipeline in case of piped gas connection. In case of LPG, for best results it would be advisable to fit it on the fascia of Kitchen Platform cabinets. TrueSafe has provision of louvers on the front and the back. Gas can leak either near Cylinder/Pipe or the Gas Stove. Someone may forget to light the gas after turning ON the Gas Stove knob or flame can extinguish while cooking. In such case LPG shall settle down because it is heavier than the air and enter the detector from the front louvers. Gas leaking from the Cylinder can enter from the louvers at the back. In case of Piped Natural Gas (PNG) detector must be fitted near ceiling.
A: With our optional gas shut-off valve, the gas can be turned off automatically. This is important if there is not likely to be a competent person around - for example if there is only a confused or elderly person present.
A: Each type of gas has its own unique chemical composition. It is this composition that the detector focuses on to detect the presence of gas. Sensors within the detector must be designed specifically for a gas. Hence a different detector is needed for each different type of gas.
A: Yes, all detectors come with relays that can be used to trigger remote alarms or monitoring systems. A: We recommend the use of a remote alarm sounder. This can be placed outside the room and will warn people of dangerous levels of gas. We recommend a notice is placed near there to instruct people what to do if the alarm sounds.
A: There is NO ABSOLUTE RULE in determining the number of gas sensors and their location. However, there are a few simple guidelines, which will help you to plan. Keep in mind that sensors monitor a point as opposed to an area. If the gas leak does not reach the sensor then no alarm will be raised. Therefore, it is extremely important to carefully select the sensor location. There are two approaches to gas sensor location: perimeter protection or point detection. With perimeter detection you place sensors all around the perimeter of the space in question to make sure you monitor the whole space. This is North, South, East and West. With point detection you locate a sensor at a position where you are concerned about a leak e.g. compressors, expansion valves, mechanical joints, or cable duct trenches. Locate the sensors no farther than 1.5m from the potential “leak source”.
A: TrueSafe is type tested from two reputed Govt Labs, namely SAMEER & ARAI. We have obtained test certificates which entitle us to put CE mark on our product. CE Mark is a European Safety norm. Test certificates could be made available upon request.
BinConnect is an intelligent product from Vighnaharta which perfectly suits the requirements of a Smart City Solid Waste Management. It is a garbage bin fill level sensor integrated with GSM and GPS connectivity with a host of other useful features.
It is configurable to use with single or 3 bins as per user requirement.
Another unique feature of BinConnect is that it connects to the cloud based application over GPRS connectivity. The BinConnect has an inbuilt GPS module that can be used to track the position of mobile bins. Additionally, it has an in-built temperature sensor. All these parameters are made available on the cloud.
BinConnect is a battery operated device. Frequency of data transmission to cloud is user configurable.
BinConnect comes with IP65 grade enclosure making its operation waterproof.
Data Type: Container fill level, GPS coordinates, Temperature.
Single Ultrasonic Level Sensor
Sensing distance – 150mm – 4000mm
• 5 years with 1 transmission per day
• 2 years with 4 transmissions per day
• 24x7 access through BinConnect web portal/Clients existing portal
